equipment for autoclaved aerated concrete block production
Basic Info
Model No.: 20000-150000 m3/year
Product Description
Mingyuan is an AAC Block Equpment manufacturer, the capacity can be up to 300000 cubic meters per year, and the raw material usually is fly ash or sand, the main equipment for aac block plant are crusher, ball mill, cutting machine, autocalves, boiler, and so on. welcome to send your inquiry about our Equpment For AAC production plant
General introduction about the production process about Equipment For aac block/equipment for aac plant/Equpment For AAC production plant
The production process of aac block with sand and fly ash share almost the same process, the main difference lies that the sand should be ground before
slurry making, while it is not necessary to grind the fly ash. The general process mainly includes :
- raw material preparation-- with fly ash as the main material, lime needs to be ground into powder which will be converted into slurry in the next stage, usually it is crushed by a jaw crusher, in order to prevent the environment from polluted, the dust collectors are adopted to collect the dusts during the production
- Batching ---in order to guarrantee the good characterics of the aac block, Each element is calculated before mixing.
- Mixing and pouring--After batching, each material will be fed to the Mixer for slurry making, and the moulds are under the pouring machine, which will pour the slurry to the moulds when it's thoroughly mixed.
- Pre-curing---The mould with slurry will be stored in the curing room for about two hours, with 40-45 celsius degree.
- Cutting-Then the green cake will be dragged out and the frame of the mould will be removed by a crane, then it will be sent to the cutting machine
- The cutting machine will cut the green cake into the sizes required, there are vertical cutting and horizontal cutting. and the waste is returned to the mixing machine for recycling, below are some commonly used aac block size, Length (mm): 600
Width (mm): 75, 100, 125, 150, 175, 200, 250
Height (mm): 200, 240, 250, 300
Remarks: The size can be customized - After cutting, the green blocks are organized into groups, which will be loaded into the autoclave when it's enough for one autoclave.
- Steaming--The green blocks are steamed for 8-10 hours with boiler as the heat source. and the pressure inside the autoclave needs to be kept at 1.2MPa, after steaming, we can get the finished aac block or aac brick, after packing, it can be sent to the warehouse or markets. AAC Block Making Plant
Equipment For AAC Block Plant or AAC Block Production Line, simply called as AAC Manufacturing Plant, it is a complex processing system with sand or fly ash as the main raw material, on one hand, fly ash is a common industrial waste, so fly ash aac block manufacturing plant can recycle the waste, which can save storage space, on the other hand, it's not necessary to grind the fly ash, so aac block making plant with fly ash is more cost effective than with sand.
Features of Equipment For aac block/equipment for aac plant/Equpment For AAC production plant
1. Lightweight: Porosity achieve 70% to 85%, volume density is generally 500-900kg/m3, as 1/5 of general concrete brick, the 1/4of clay brick, the 1/3 of hollow brick, and similar with wood can float in water. It can reduce building weight, reduction in the cost of integrated building, moreover, prolong building's life.
2. Fireproof: Most of the major raw materials is inorganic materials, so it has good fire resistance, and do not emit harmful gases when meet fire. Fire 650 degrees, as a refractory material, the thick up of 100 mm walls can reach to 4 hours fire resistance, 300mm thick up wall can reach to 9 hours fire resistance.
3. Sound insulation: Due to a unique porous structure, so it has a sound absorption capacity. The sound absorption capacity can reach of 100mm thick wall up to 41 db.
4. Insulation: As the material inside has a large numbers of the pores and porous, which has a good thermal insulation properties. The Thermal conductivity is 0.11-0.16W/MK, as 1/4-1/5 of brick. Typically, the insulation effect of 20cm thick aerated concrete wall is equivalent to 49cm thick solid brick walls ordinary.
5. Permeability: Result of material by the composition of many independent small pores, the moisture absorption is slow, in the volume of absorbent is 5 times of clay saturation do. When used in the bathroom, the wall can be treated to interface directly paste tiles.
6. Anti-seismic: The same building structure, improve the two seismic than the brick level.
7. Green: Manufacturing, transportation, all use the process of non-pollution, to protect arable land, saving energy, is one kind of a green building material.
Below is the proportion of each element about Equipment For aac block/equipment for aac plant/Equpment For AAC production plant
Name Unit Cement Lime Sand Sand % 55-65 Cement % 10-20 Lime % 20-30 Gypsum % 2-3 Aluminum powder paste(600kg/m3) 1/10000 8 Water & material rate 0.65-0.75 Casting system OC 35-38 Aluminum mixing time S 30-40
Proportion of each element about Equipment For aac block/equipment for aac plant/Equpment For AAC production plant
name | unit | Cement lime fly ash |
flash | % | 65-70 |
cement | % | 6-15 |
lime | % | 18-25 |
gypsum | % | 3-5 |
Aluminum powder paste(600kg/m3) | 1/10000 | 8 |
Water & material rate |
| 0.60-0.65 |
Casting system | OC | 36-40 |
Aluminum mixing time | S | 30-40 |
Main Specification of cutting machine that used as Equipment For aac block/equipment for aac plant/Equpment For AAC production plant
Moel No. m | Capacity m3/year | Cutting Step-in mm | Cutting Precision mm | Production Cycle Time min | Power kW |
4.2X1.2X0.6 | less than 200,000 | 5 (2.5) / 10 | ±3±1±1 | ≤6 | 25 |
4.8X1.2X0.6 | 200,000~250,000 | 5 (2.5) / 10 | ±3±1±1 | ≤6 | 25 |
6.0X1.2X0.6 | 250,000~300,000 | 5 (2.5) / 10 | ±3±1±1 | ≤6 | 27.5 |
Product Categories : AAC Block Manufacturing Plant > Fly Ash Aac Production Plant