All Kinds Of Bulk Nails
|Terms of Trade:||FOB,CIF|
|Min. Order:||10 Bag/Bags|
|Delivery Time:||30 Days|
|Place of Origin:||China|
Model No.: 8d
Flat Head: Double Head
Common Nail. As the name suggests, these are your everyday nails. Used for rough construction work, the common nail can be purchased in lengths varying from one to six inches (2d to 60d). The largest common nails are colloquially known as spikes.
Box Nail. These look like common nails, but are thinner. This means they are less likely to cause splits in the wood; as they displace less wood, they also have less holding power, so are not generally used where structural strength is critical. Box nails are generally available in lengths from one inch to three and a half inches.
Finishing Nail. Finishing nails are (surprise, surprise) used for finish work. When the nailhead will show in the final product (as with moldings, for example), finishing nails are often used because their barrel-shaped heads are small and can be driven below the surface of the wood using a nail set (a technique called countersinking). Finishing nails are generally available in lengths ranging from one to four inches (2d to 20d).
Casing Nail. A near relation of the finishing nail, the casing nail is slightly larger and has increased holding power. It is most often used for attaching moldings such as window and door casings where added strength is required.
Brad. Brads are essentially diminutive finishing nails, proportionately smaller in diameter and length (one inch or less). They are used in making frames, attaching plywood paneling, and in cabinetwork.
Roofing Nail. Roofing nails have disproportionately large, round heads and heavier shafts for their length. They are designed to hold roofing materials in place, in particular composition and asphalt- based materials. In order to resist rust, roofing nails are heavily galvanized or made of aluminum. Three-quarter-inch to one-and-three- quarter-inch sizes are usual; the penny system is not used in reference to roofing nails.
Masonry Nail. Several types of masonry nails are sold; all are designed to be driven into brick or concrete walls. These hard nails may be rectangular in section or have fluted shafts, but all are hardened to resist bending and breaking as they are driven into almost rock-hard materials. Given the nature of masonry materials, be sure to wear safety glasses or goggles when nailing masonry nails, as flying chips pose a danger to your eyes.
Cut Flooring Nail. The lone surviving direct descendant of the once-dominant cut nail is the flooring nail. These nails are large, strong, and are often used in a nailing machine.
Spiral Flooring Nail. Spiral flooring nails feature a spiraled shaft and were traditionally used for nailing subfloors. Nail guns and the specially designed nails used in them have superseded these nails in much construction work today.
Annular Ring Nail. Often sold in galvanized steel, annular ring nails are commonly used as siding nails, to hold clapboards or shingles in place, or for underlayment or paneling. They are thin, lined with rings for added holding power, and resistant to rust.
Duplex Nail. This is a variation of the common nail. Featuring a second head formed a short distance down the shaft from the end ot the nail, the duplex nail is used for temporary construction (like scaffolding and staging) because it can be driven snug, yet be easily removed.
Other Nails. Drywall nails, which feature rings on their shafts, are sold for hanging wallboard; their heads are traditionally driven slightly below the surface of the plaster panel (the hammer stroke creates a dimple that is then filled in with joint compound or plaster). Cement-coated nails are roughly the size and weight of box nails, but are coated with a resin for added holding power. They`re used to nail outside sheathing.
Many of the varieties of nails discussed above are also sold in magazines for use in air-powered nailers. Framing, finishing, and roofing nails, as well as brads and flooring nails, are commonly available for such equipment.
Huanghua Yuanfeng Hardware Products Co., Ltd is located in the industry park of Jiucheng, Huanghua city, It is adjacent to NO.307 national road and in the center of Bohai Sea Economic Rim and has convenient traffic and communications.
With Bohai to the east,Shandong to the south and Tianjin Beijing to the north, it has a lot advantages for the transportation. In addition, it also close to the Huanghua Port and the Tianjin Port, the freeways of Shijiazhuang-Huanghua and of Tianjin-Shanwei make the distances from factory to ports much closer. Bohai New Area is the important economic and technological development zone of Hebei Province. Our company will grow up together with the Industry Park.
The company mainly produces hardware products, which are widely used in building, gardening, freeways and railways. Products are all for exportation, and most of them are exported to Europe and America.
We have acquired CE Certificates for our products.
We have the professional and technical personnel to support our quality, so that we can supply good and reliable services to our customers. With the spirit of [ survive on quality, reputation and development", we will keep improving , and growing stronger together with our customers hand in hand.
- Company Name: Huanghua Yuanfeng Hardware Products Co.,Ltd
- Representative: Suli Fan
- Product/Service: Galvanized Wiremesh , Iron Wire , Pole Anchor , Green Graden Stake , Garden Products , Steel Posts
- Capital (Million US $): 500000
- Year Established: 2014
- Total Annual Sales Volume (Million US $): Below US$1 Million
- Export Percentage: 91% - 100%
- Total Annual Purchase Volume (Million US $): Below US$1 Million
- No. of Production Lines: 2
- No. of R&D Staff: Fewer than 5 People
- No. of QC Staff: Fewer than 5 People
- OEM Services Provided: no
- Factory Size (Sq.meters): 1,000-3,000 square meters
- Factory Location: North of NO. 307National Road,Jiucheng Park,Huanghua City
- Contact Person: Ms. Amy
- Tel: 86-317-5888987